Skip to main content

Service Data for the Isuzu MU Wizard

While doing research for my Isuzu MU Wizard (UCS69), I found that there was not that much information freely available online. It was also very difficult to find the owners' manual. In the end, I downloaded a PDF copy of a scanned manual which was shared on www.planetisuzoo.com. If you are new to Isuzu vehicles, then this is best place to start. 

Anyway, I've decided to share the basic service data from the booklet here in the hopes that it will make your life easier when doing service for your Isuzu. 

This is basically for the 4JG2 engine model. 


Item

Capacity

Replacement Period

Recommended Brand

Brake fluid Below maximum level on the tank Every 2 years  
ATF 8.0L Every 2 years  
Transfer oil 1.45L Every 40,000 km (2 years)  
Front differential oil 1.5L Every 40,000 km (2 years)  
Rear differential oil 1.8L Every 40,000 km (2 years)  
Wheel bearing grease   Every 40,000 km  
Engine oil Approx 7.3L Every 5,000 km  
Oil filter   Every 10,000 km  
Fuel filter   Every 60,000 km  
Air cleaner element   Every 40,000 km  
Timing belt   Every 100.000 km  
Radiator 8.2L Every 5 years  
Fuel tank 85L   Diesel

 

Comments

Popular posts from this blog

List of Repairs to Do on the Isuzu MU Wizard

So I’ve decided to publish a list of things that need to be done on the Isuzu MU Wizard. I started the list on initial inspection of the vehicle but after removing the tires, I’ve noted a few other things that need to be done. There is a tilt so the torsion bars need to be adjusted. Brake cable . The most obvious work that needs to be done is to get the parking/emergency brake cables replaced. I might also replace the rotors and brake pads.  The windows and doors need to be fixed .  Suspensions . The rear sway bar is broken and also bushings might need to be replaced. I also felt like weight was being shifted too much to one side when turning. This is not good.  CV axle . These have been removed for both sides so I will have to have them replaced.  Wheel hub assembly? I plan to have this done but it’s not a priority yet. Seats and interior. I will also have to get the seats fixed and the interior cleaned. It is a mess at the moment.  Torsion bar ...

Still here, but...

HELLO!  Its been a while since I last posted an updated and I'm sure you are wondering what's been happening. Well, life is happening and I don't seem to have enough time to blog, but there have been some positive new, and some bad too! You cant have it either way. The good news first! The good news is that I managed to find shock absorbers for the MU Wizard. It took me a while but I found them in Papua New Guinea's second largest city, Lae.  We were driving around after a meeting when I spotted a Motorist Discount Center (MDC) and asked the driver to stop. I got the suspension parts for around K280.  Now they are standard shock absorbers for both front and rear. The models for my vehicle were not available but the salesman offered parts that were meant for the Isuzu Bighorn and TR (Faster) which actually share the same chassis.  The only things left are the suspension bushings and coil springs.    I haven't done the installation yet....

Ball Joints and Wheel Bearings Replaced

So after a long hiatus we have finally started some work on our Isuzu MU Wizard. The first thing we did was replace the ball joints.  The ball joints had reached the point where it would fall off any time. It would squeak whenever I hit a hump/bump or turned a corner. This led to me grounding the Wizard for almost 6 months.  I know its a long time but I was caught up with work that there was very little time during the day to work on the SUV. Fortunately, I'm starting 2021 with catching up with the vehicle's maintenance.  Last week we replaced all the ball joints and outer wheel bearings. All parts were sourced from Pacific Engineering in Port Moresby.  The ball joints did not require special tools - ball joint puller, etc - but it did require some elbow grease and breaker bar.  While the ball joints were out, we also decided to check the wheel bearings - and yes - they were also kaput. We ended up replacing them as well. We have also identified that the tie rod...